- Remove water and replace with syscalls for tun setup
- Support named interfaces
- Set up routes with syscalls instead of os/exec
Co-authored-by: Wade Simmons <wade@wades.im>
This allows you to configure remote allow lists specific to different
subnets of the inside CIDR. Example:
remote_allow_ranges:
10.42.42.0/24:
192.168.0.0/16: true
This would only allow hosts with a VPN IP in the 10.42.42.0/24 range to
have private IPs (and thus don't connect over public IPs).
The PR also refactors AllowList into RemoteAllowList and LocalAllowList to make it clearer which methods are allowed on which allow list.
This change is for Linux only.
Previously, when running with multiple tun.routines, we would only have one file descriptor. This change instead sets IFF_MULTI_QUEUE and opens a file descriptor for each routine. This allows us to process with multiple threads while preventing out of order packet reception issues.
To attempt to distribute the flows across the queues, we try to write to the tun/UDP queue that corresponds with the one we read from. So if we read a packet from tun queue "2", we will write the outgoing encrypted packet to UDP queue "2". Because of the nature of how multi queue works with flows, a given host tunnel will be sticky to a given routine (so if you try to performance benchmark by only using one tunnel between two hosts, you are only going to be using a max of one thread for each direction).
Because this system works much better when we can correlate flows between the tun and udp routines, we are deprecating the undocumented "tun.routines" and "listen.routines" parameters and introducing a new "routines" parameter that sets the value for both. If you use the old undocumented parameters, the max of the values will be used and a warning logged.
Co-authored-by: Nate Brown <nbrown.us@gmail.com>
During shutdown, this will keep Nebula alive until after sshd is finished. This cleanly terminates ssh clients accessing a server over a Nebula tunnel.
This commit adds support for Nebula to be started without creating
a tun device. A node started in this mode still has a full "control
plane", but no effective "data plane". Its use is suited to a
lighthouse that has no need to partake in the mesh VPN.
Consequently, creation of the tun device is the only reason nebula
neesd to be started with elevated privileged, so this example
lighthouse can also be run as a non-root user.
Currently, we wait until the next timer tick to act on the lighthouse's
reply to our HostQuery. This means we can easily add hundreds of
milliseconds of unnecessary delay to the handshake. To fix this, we
can introduce a channel to trigger an outbound handshake without waiting
for the next timer tick.
A few samples of cold ping time between two hosts that require a
lighthouse lookup:
before (v1.2.0):
time=156 ms
time=252 ms
time=12.6 ms
time=301 ms
time=352 ms
time=49.4 ms
time=150 ms
time=13.5 ms
time=8.24 ms
time=161 ms
time=355 ms
after:
time=3.53 ms
time=3.14 ms
time=3.08 ms
time=3.92 ms
time=7.78 ms
time=3.59 ms
time=3.07 ms
time=3.22 ms
time=3.12 ms
time=3.08 ms
time=8.04 ms
I recommend reviewing this PR by looking at each commit individually, as
some refactoring was required that makes the diff a bit confusing when
combined together.
This change add more metrics around "meta" (non "message" type packets).
For lighthouse packets, we also record statistics around the specific
lighthouse meta type.
We don't keep statistics for the "message" type so that we don't slow
down the fast path (and you can just look at metrics on the tun
interface to find that information).
These settings make it possible to blacklist / whitelist IP addresses
that are used for remote connections.
`lighthouse.remoteAllowList` filters which remote IPs are allow when
fetching from the lighthouse (or, if you are the lighthouse, which IPs
you store and forward to querying hosts). By default, any remote IPs are
allowed. You can provide CIDRs here with `true` to allow and `false` to
deny. The most specific CIDR rule applies to each remote. If all rules
are "allow", the default will be "deny", and vice-versa. If both "allow"
and "deny" rules are present, then you MUST set a rule for "0.0.0.0/0"
as the default.
lighthouse:
remoteAllowList:
# Example to block IPs from this subnet from being used for remote IPs.
"172.16.0.0/12": false
# A more complicated example, allow public IPs but only private IPs from a specific subnet
"0.0.0.0/0": true
"10.0.0.0/8": false
"10.42.42.0/24": true
`lighthouse.localAllowList` has the same logic as above, but it applies
to the local addresses we advertise to the lighthouse. Additionally, you
can specify an `interfaces` map of regular expressions to match against
interface names. The regexp must match the entire name. All interface
rules must be either true or false (and the default rule will be the
inverse). CIDR rules are matched after interface name rules.
Default is all local IP addresses.
lighthouse:
localAllowList:
# Example to blacklist docker interfaces.
interfaces:
'docker.*': false
# Example to only advertise IPs in this subnet to the lighthouse.
"10.0.0.0/8": true
* add configurable punching delay because of race-condition-y conntracks
* add changelog
* fix tests
* only do one punch per query
* Coalesce punchy config
* It is not is not set
* Add tests
Co-authored-by: Nate Brown <nbrown.us@gmail.com>
This change exposes the current constants we have defined for the handshake
manager as configuration options. This will allow us to test and tweak
with different intervals and wait rotations.
# Handshake Manger Settings
handshakes:
# Total time to try a handshake = sequence of `try_interval * retries`
# With 100ms interval and 20 retries it is 23.5 seconds
try_interval: 100ms
retries: 20
# wait_rotation is the number of handshake attempts to do before starting to try non-local IP addresses
wait_rotation: 5
This change introduces logging.timestamp_format, which allows
configuration of the Logrus TimestampFormat setting. The primary purpose
of this change was to allow logging with millisecond precision. The
default for `text` and `json` formats remains the same for backwards
compatibility.
timestamp format is specified in Go time format, see:
- https://golang.org/pkg/time/#pkg-constants
Default when `format: json`: "2006-01-02T15:04:05Z07:00" (RFC3339)
Default when `format: text`:
when TTY attached: seconds since beginning of execution
otherwise: "2006-01-02T15:04:05Z07:00" (RFC3339)
As an example, to log as RFC3339 with millisecond precision, set to:
logging:
timestamp_format: "2006-01-02T15:04:05.000Z07:00"
Chad Harp